Out of the Mold

Mold Risk Calculator

Enter your indoor humidity and temperature to see your mold risk in seconds. Mold needs sustained moisture to grow, and the EPA says to keep indoor humidity below 60% (ideally 30–50%). This tool tells you where you stand, shows the dew point that drives condensation, and recommends the right dehumidifier size for your space.

Check Your Mold Risk

Enter your indoor conditions to see your risk level and what to do.

% RH

Read this off any $10 hygrometer. Not sure? Damp basements often run 60–80%.

°F
sq ft
High risk65% RH · dew point 58°F

Past the EPA limit — mold-friendly conditions

Above 60% RH you're past the level the EPA says to stay under. Porous materials like drywall, wood, and fabric can hold enough moisture for mold to take hold within 24–48 hours. This is the point to run a dehumidifier continuously and find the moisture source.

Any surface colder than 58°Fwill collect condensation at these conditions — that's why mold shows up first on windows, exterior walls, and uninsulated pipes. Warming cold surfaces or lowering humidity both push the dew point down.

Recommended dehumidifier size

At 65% RH your space reads as slightly to moderately damp (musty odor). For 800 sq ft, ENERGY STAR recommends a 20–30 pints/dayunit. It's better to oversize than undersize.

Best fit for a living space or basement

  • hOmeLabs 50-Pint Energy Star Dehumidifier

    $220–260 · Whole-basement and large-room mold prevention at the best price-to-capacity ratio

    View on Amazon
  • Midea 50-Pint Energy Star Dehumidifier

    $180–220 · Budget-conscious buyers who still need full 50-pint capacity

    View on Amazon
  • Midea Cube 50-Pint Smart Dehumidifier with Pump

    $270–320 · Basements without a floor drain, or anyone who wants remote humidity monitoring

    View on Amazon
Compare all 3 in your Amazon cart

Want the full picture on picking and sizing a unit? Read our dehumidifier-for-mold guide.

Risk tiers follow the EPA guidance to keep indoor humidity below 60% (ideally 30–50%). Sizing follows ENERGY STAR. This tool estimates risk from a single reading — actual mold depends on how long conditions persist and where moisture collects.

Already smell something musty? Here's what that means

Affiliate Disclosure: Out of the Mold is reader-supported. As an Amazon Associate, we may earn a commission when you buy through links on this page — at no extra cost to you. Our picks are based on independent standards, manufacturer specifications, and published research, not commissions.

The humidity levels that cause mold

Mold spores are floating in the air of virtually every home — what decides whether they grow is moisture. The single most useful number you can control is relative humidity. The EPA recommends keeping indoor humidity below 60 percent, and ideally between 30 and 50 percent (retrieved 2026-09-26). Here is how the calculator reads your number:

  • 30–50% RH — Low risk.You're in the EPA's ideal range. Mold stays dormant.
  • 51–60% RH — Moderate. Below the ceiling but above ideal; cold surfaces can still condense and grow mold locally.
  • 61–70% RH — High. Past the EPA limit. Drywall, wood, and fabric can support mold within 24–48 hours.
  • Above 70% RH — Severe. Active mold-growth conditions; expect visible growth and musty odors if it persists.

Why temperature (dew point) matters too

Humidity alone doesn't tell the whole story. Every combination of temperature and humidity has a dew point— the temperature at which the air becomes saturated and water condenses out. When any surface in the room is colder than that dew point, it grows a film of liquid water, and that water is what mold feeds on. It's why window sills, exterior wall corners, and AC coils and vents mold before anything else in a room. The calculator shows your dew point so you know how cold a surface has to be before it starts sweating.

What size dehumidifier stops mold

If your risk is Moderate or higher, a dehumidifier is the most reliable fix — it holds humidity below the mold threshold automatically. Sizing depends on how damp the space is and how big it is. These are the ENERGY STAR recommendations (retrieved 2026-09-26):

DampnessUnder 2,000 sq ftOver 2,000 sq ft
Slightly to moderately damp (musty odor)20–30 pints/day30+ pints/day
Very damp (visible damp spots)25–40 pints/day40+ pints/day
Wet (sweating walls, seepage)30–50 pints/day50+ pints/day

Source: ENERGY STAR — Dehumidifiers (sizing guidance) (retrieved 2026-09-26). ENERGY STAR advises it's better to oversize than undersize.

For the full walkthrough on choosing between models, drainage options, and where to place the unit, see our best dehumidifiers for mold guide. If the mold is already visible, start with our step-by-step removal guide or estimate the job with our mold removal cost calculator.

Frequently Asked Questions

What humidity level causes mold?
Mold risk climbs sharply once indoor relative humidity stays above 60%. The EPA recommends keeping indoor humidity below 60 percent, and ideally between 30 and 50 percent, to control mold. Above 60% RH, porous materials like drywall and wood can hold enough moisture for mold to take hold within 24 to 48 hours.
What is a safe indoor humidity level to prevent mold?
The EPA's ideal range is 30 to 50 percent relative humidity, with 60 percent as the upper limit you should not exceed. Setting a dehumidifier's humidistat to around 45 to 50 percent keeps most homes comfortably inside the safe zone year-round.
Does temperature affect mold risk?
Temperature matters through the dew point. When a surface is colder than the air's dew point, water condenses on it, and that liquid moisture is what mold needs to grow. This is why mold appears first on cold windows, exterior walls, and uninsulated pipes even when the room's overall humidity seems moderate. Warming cold surfaces or lowering humidity both reduce condensation.
What size dehumidifier do I need to stop mold?
It depends on your space size and how damp it is. Per ENERGY STAR, a slightly-to-moderately damp room under 2,000 sq ft needs a 20–30 pint/day unit; a very damp space needs 25–40 pints; and a wet space with sweating walls needs 30–50 pints. Larger spaces need more. ENERGY STAR advises it's better to oversize than undersize.
How do I measure the humidity in my house?
Use a hygrometer — an inexpensive digital humidity gauge (often $10–20) that also reads temperature. Place it in the room you're worried about, away from vents and windows, and let it settle for an hour. Damp basements and crawl spaces commonly read 60–80% RH, which is well into mold-risk territory.

High risk? Get the humidity under control.

The fastest way to shut down mold growth is to pull humidity back below 50%. See which dehumidifier fits your space and budget.